| ..........Nøkkelring - Alkoholtester |
- MÃ¥ler alkoholen i blodet fra 0,10 til 1,20 promille.
- Meget nøyaktig (dersom du har KALIBRERT den).
- Liten; du har den alltid med deg, på grunn av nøkkel-ringen.
- Det perfekte produkt 'dagen der på' , særlig ved Julebord tider.
- Innebygget LYKT og GASS - detektor.
-..Drives av 1 AAA batteri, som varer ca. 2 år (Sett i nytt).
- 1 års Garanti, og ny Gratis om noe er feil (ikke batteriet).
- Du blir midtpunktet i alle selskaper, med 'Safe Drive'.
- CE og TUV godkjent.
- Meget nøyaktig (dersom du har KALIBRERT den).
- Liten; du har den alltid med deg, på grunn av nøkkel-ringen.
- Det perfekte produkt 'dagen der på' , særlig ved Julebord tider.
- Innebygget LYKT og GASS - detektor.
-..Drives av 1 AAA batteri, som varer ca. 2 år (Sett i nytt).
- 1 års Garanti, og ny Gratis om noe er feil (ikke batteriet).
- Du blir midtpunktet i alle selskaper, med 'Safe Drive'.
- CE og TUV godkjent.
Det er 4 ting som er viktig, for at Nøkkel-ring Alkotesteren
skal virke riktig ( Les bruksanvisningen nøye ) :
1. KALIBRER Alkoholtesteren, i helt EDRU tilstand, før bruk.
Hold Alkohol-måler 'knappen' inne i mer enn 5 sec (max. 10sec.).
Vent til GRØN LED lyser konstant (Grønn-rødt, grønn-rødt-grønn; ca.
15sec.).
Blås inn i alkoholtesteren (ca. 5sec.).
2. Vent 30 minutter etter siste drink, før du blåser, for å oppnå best resultat.
3. Hold 'på' knappen inne i 2-3 sec. (mindre enn 5 sec., ellers kalibrerer du),
og vent med å blåse til GRØN LED lyser (ca 10 sec.).
4. Blås sakte inn i hullet i ca. 5 sec.
Fargen på den blinkende LED,en forteller ditt alkohol-nivå.
GJENTA PUNKT 3 OG 4 FLERE GANGER, FOR BEST RESULTAT.
Alkoholtesteren er kun en indikator, på din promille,
og vi kan ikke garantere at du ikke har promille, selv om den lyser grønt.
Vi tar heller ikke noe ansvar om den viser feil, annet at du får ny innen 1 år
(ta vare på kviteringen), dersom det er noe feil med den ( gjelder ikke batteriet).
Et gjenomsnits menneske forbrenner ca. 0,15 promille i timen (fra 0,1 til 0,25).
En stor voksen mann kan forbrenne 0,25 promille i timen, mens en liten jente
kan forbrenne 0,1 promille i timen.
Husk ! Det er best å ikke drikke noe alkohol, før du skal kjøre bil.
Mener du at 'Safe Drive' måler feil promille, gjør som følger :
- Sett inn et nytt batteri (Sett batteriet riktig vei, og det må ikke ha gått ut på
dato ).
- Kalibrer, som beskrevet over og i bruksanvisningen, i helt edru tilstand.
- Gjenta (punkt 3 og 4 over) promille målingen flere ganger (minst 3).
Hjelper ikke dette, kontakt meg via E-mail, forklar feilen og oppgi fullt navn,
adresse og oppgi hvor og når du kjøpte den.
skal virke riktig ( Les bruksanvisningen nøye ) :
1. KALIBRER Alkoholtesteren, i helt EDRU tilstand, før bruk.
Hold Alkohol-måler 'knappen' inne i mer enn 5 sec (max. 10sec.).
Vent til GRØN LED lyser konstant (Grønn-rødt, grønn-rødt-grønn; ca.
15sec.).
Blås inn i alkoholtesteren (ca. 5sec.).
2. Vent 30 minutter etter siste drink, før du blåser, for å oppnå best resultat.
3. Hold 'på' knappen inne i 2-3 sec. (mindre enn 5 sec., ellers kalibrerer du),
og vent med å blåse til GRØN LED lyser (ca 10 sec.).
4. Blås sakte inn i hullet i ca. 5 sec.
Fargen på den blinkende LED,en forteller ditt alkohol-nivå.
GJENTA PUNKT 3 OG 4 FLERE GANGER, FOR BEST RESULTAT.
Alkoholtesteren er kun en indikator, på din promille,
og vi kan ikke garantere at du ikke har promille, selv om den lyser grønt.
Vi tar heller ikke noe ansvar om den viser feil, annet at du får ny innen 1 år
(ta vare på kviteringen), dersom det er noe feil med den ( gjelder ikke batteriet).
Et gjenomsnits menneske forbrenner ca. 0,15 promille i timen (fra 0,1 til 0,25).
En stor voksen mann kan forbrenne 0,25 promille i timen, mens en liten jente
kan forbrenne 0,1 promille i timen.
Husk ! Det er best å ikke drikke noe alkohol, før du skal kjøre bil.
Mener du at 'Safe Drive' måler feil promille, gjør som følger :
- Sett inn et nytt batteri (Sett batteriet riktig vei, og det må ikke ha gått ut på
dato ).
- Kalibrer, som beskrevet over og i bruksanvisningen, i helt edru tilstand.
- Gjenta (punkt 3 og 4 over) promille målingen flere ganger (minst 3).
Hjelper ikke dette, kontakt meg via E-mail, forklar feilen og oppgi fullt navn,
adresse og oppgi hvor og når du kjøpte den.
Best.nr. 1020
kr. 399,-
kr. 399,-
'Safe Drive' leveres i Blister-pakke, med Barkode
og kommer 6 st. i en flipp-opp Display eske.
Engros prisen er kr. 69,90 pr. st. (ex. mva.) ved kjøp av min. 12 st.
og kommer 6 st. i en flipp-opp Display eske.
Engros prisen er kr. 69,90 pr. st. (ex. mva.) ved kjøp av min. 12 st.
A5 brosjyre i farger kan leveres gratis !
MÃ¥l: 5,7 x 3,4 x 1,3
cm
cm
Blåse
hull
<---
hull
<---
Digital Alkoholtester
0,10-1,90 promille
Med Timer: 0-10t
Ink batterier
kr.399,- (ink. mva.)
Engros pris ex. mva:
kr.199,-
0,10-1,90 promille
Med Timer: 0-10t
Ink batterier
kr.399,- (ink. mva.)
Engros pris ex. mva:
kr.199,-
kr. 139,-
1 Ã…rs
Garanti !
Garanti !
Arngren.Topp- 30.produkter
Lykt
O
<- Batteri -luke (1 st. AAA)
Husk ! MÃ¥ler Alkotesteren
feil,
sett i nytt Batteri.
feil,
sett i nytt Batteri.
Tilbud !
-----
Leveres med gammelt Batteri. Du MÃ… sette i
nytt
nytt
.
kr. 99,80 pr. st. ved kjøp av 6 st.
Digital Alkoltester CA-2000
Nå har jeg prøvd mange forskjellig Alkotestere,
i mange prisklasser fra kr. 100,- opp til kr. 2000,-
CA-2000 er den beste jeg har prøvd uansett pris.
Dette er en Alkotester du kan stole på.
- Måleområde : 0,0 - 4.00 promille
- Nøyaktighet : + - 0,02 promille.
Mer nøyaktig en den Politiet bruer ( + - 0,05 promille)
- Display : 3 x LCD tall
- Strøm : 9V batteri eller 12Vdc Biladapter (Følger med)
- Vekt : 200g ink. 9V batteri.
- MÃ¥l : 12 x 6 x 2,5 cm
Levers med 5 vaskbare plastikk-munnstykker, etui,
bærestropp, 12Vdc Billader, 9Vdc batteri, og Bruksanvisning
( Se tekniske date under ).
Best.nr. 1023 kr. 698,-
( 2 st. kr. 1198,- / 599,- pr. st. )
Nå har jeg prøvd mange forskjellig Alkotestere,
i mange prisklasser fra kr. 100,- opp til kr. 2000,-
CA-2000 er den beste jeg har prøvd uansett pris.
Dette er en Alkotester du kan stole på.
- Måleområde : 0,0 - 4.00 promille
- Nøyaktighet : + - 0,02 promille.
Mer nøyaktig en den Politiet bruer ( + - 0,05 promille)
- Display : 3 x LCD tall
- Strøm : 9V batteri eller 12Vdc Biladapter (Følger med)
- Vekt : 200g ink. 9V batteri.
- MÃ¥l : 12 x 6 x 2,5 cm
Levers med 5 vaskbare plastikk-munnstykker, etui,
bærestropp, 12Vdc Billader, 9Vdc batteri, og Bruksanvisning
( Se tekniske date under ).
Best.nr. 1023 kr. 698,-
( 2 st. kr. 1198,- / 599,- pr. st. )
PRODUCT SYNOPSYS
Highly Reliable, accurate and quick breath alcohol analyzer
CA-2000 is an unique & highly-sophisticated alcohol analyzer,
utilizing the variation of electrical property value
of the oxide-semiconductor,
when the alcohol substance is detected.
And, with the development of new ceramic material
combined with relevant catalyst,
it can selectively analyze the alcohol concentration to the
ppm unit existing in the human breath.
Our laboratory made it in developing the
highly-selective semi-conductive sensor,
reactive to alcohol substance,
which can be differentiated from the other
semi-conductive sensor products
(which are often affected by other substances
like smokes and smells of food).
Furthermore, it did improve to the large extent the standby,
response & recovery time which could be crucial
in measuring gas concentration.
- Detection mechanism of our unique semi-conductive sensor
When the oxide having the property of n-type conductivity
is open to the atmosphere, it decreases the number of electron
affecting on electrical property by the adsorbed oxygen,
and results in increasing the resistance.
And, afterwards, if the specific gas (reducing gas)
exists in the atmosphere, it reacts with the adsorbed oxygen,
and increase the electron in the oxide,
resulting in decreasing the resistance.
So to speak, the electrical property of the oxide
is getting changed when a specific gas is exposed
from the outside, and our sensor can analyze
the gas concentration from the variation of quantity.
FEATURES
01. Highly reliable accuracy by the most sophisticated sensor .
CA-2000 adopts a highly-selective semiconductor sensor
(reactive to alcohol substance) designed by KAIST
(Korea Advanced Institute of Science and Technology).
CA-2000 is an unique breath tester adopting this
most sophisticated technology of sensor.
02. Stable testing data
It allows you to get stable data for successive testing.
03. Digital type ; It displays by 3 digits (0.xx% BAC/BrAC).
04. Wide detection range : 0.00 - 0.40% BAC.
05. Long-term stability .
CA-2000 can analyzes very precisely
even after long time of uses.
06. Compact & light weight hand-held device.
07. Short warm-up & response Time.
After power on, less than 20sec. of warming up count-down
(200 to 000) is needed to make it ready for testing.
And, exhaling just for a few seconds will reach you
to instantly read the testing numeric digits.
08. Longer life time : 3,000 times testing.
09. Quick Recovery Time.
The sensor of CA-2000 can be purged in 30 seconds
for another time of testing.
You don't need to be too patient to do consecutive testing.
10. Power .
9V Alkaline battery & one cigar Jack DC adapter included.
11. Sanitary Testing .
CA-2000 includes 5pcs of mouthpiece for sanitary direct testing.
12. Alarm Sound.
If you are out of legal limit range, alarm sound
will be automatically beeping.
It could be customized depending on the countries.
13. Compact design and anaesthetic outlook .
HOW TO USE
1. Turn on the PWR On/Off switch
Soon after the power on, CA-2000 will start the
count-down 200 to 000 on the display window.
It is a "Warm-up" process to make the sensor,
and circuit be ready for testing.
2. When you hear beep sound & green lighting is on READY,
please blow into for 3 seconds till you would hear
another time of "Beep" sound.
N.B. : 1. In this stage, if you don't blow within 30 seconds,
it automatically shows OFF display for turn-off
3. In case you drink quite a little
(if actual concentration would be below 0.01% BAC/0.05 mg/lBrAC),
it may not be activated.
However, it shows still 0.00% and you're said to be in safe range.
4. Then, the test result (BAC or BrAC) will be displayed
by 3 digits for 15 seconds, at the same time both READY,
and WARN lamps are flickering.
N.B. : 1. If the BAC / BrAC data would be over
0.05% / 0.25mg/l (default setting) respectively,
red WARN lamp will be flickering along with "Alarm" sound.
5. The "Alarm" level is adjustable pursuant to the local legal limit.
6. Finally, it shows "OFF" for turn-off.
7. For the successive testing, try again from No.1 to No. 3.
TO GET MORE ACCURATE TESTING DATA
After drinking, it is recommended to test after 30 min.
It is because it takes 30 min. approximately for alcohol
to be absorbed into blood, from the digestive organs.
And residual alcohol remaining in the mouth
may cause inaccurate data.
To avoid testing under strong wind or in the closed room
with contaminated air.
When the "BAT LOW "lamp is lighting on, it's advisable to
replace 9V alkaline battery.
To attain more accurate data, please repeat testing about 3 times.
TECHNICAL SPECIFICATION
- Size : 12 x 6 x 2,5 cm
- Weight : 200g
- Housing : Shock resistant, molded plastic
- Sensor : Highly selective semi-conductive oxide alcohol sensor
- Response time : 3 sec.
- Warm up time : 20 sec.
- Recovery time (sensor purge) : 30 sec.
- Battery life : About 200 tests
- Battery : 9V alkaline
- External power supply : 12V DC adapter
- Accuracy : at ± 0.01% at 0.10% BAC
at ± 0.05 mg/l at 0.50mg/l BrAC.
- Detection range : 0.00 ~ 0.40% BAC . 0.00 ~ 2.00 mg/l BrAC
- Calibration : BAC simulator (Model 34C/Guth Laboratory, USA)
- Digital display : Three digits in numeric readout
- Packing : Tester, 9V alkaline, Cigar-Jack DC adapter,
- 5 pcs of mouthpieces, Users manual, Carrying Bag .
- Measuring method : Variation of Electro- Conductivity
Deviation at 0.10% BAC : at ± 0.01% BAC
- Characteristics : High selectivity , Reasonable price , small deviation .
Highly Reliable, accurate and quick breath alcohol analyzer
CA-2000 is an unique & highly-sophisticated alcohol analyzer,
utilizing the variation of electrical property value
of the oxide-semiconductor,
when the alcohol substance is detected.
And, with the development of new ceramic material
combined with relevant catalyst,
it can selectively analyze the alcohol concentration to the
ppm unit existing in the human breath.
Our laboratory made it in developing the
highly-selective semi-conductive sensor,
reactive to alcohol substance,
which can be differentiated from the other
semi-conductive sensor products
(which are often affected by other substances
like smokes and smells of food).
Furthermore, it did improve to the large extent the standby,
response & recovery time which could be crucial
in measuring gas concentration.
- Detection mechanism of our unique semi-conductive sensor
When the oxide having the property of n-type conductivity
is open to the atmosphere, it decreases the number of electron
affecting on electrical property by the adsorbed oxygen,
and results in increasing the resistance.
And, afterwards, if the specific gas (reducing gas)
exists in the atmosphere, it reacts with the adsorbed oxygen,
and increase the electron in the oxide,
resulting in decreasing the resistance.
So to speak, the electrical property of the oxide
is getting changed when a specific gas is exposed
from the outside, and our sensor can analyze
the gas concentration from the variation of quantity.
FEATURES
01. Highly reliable accuracy by the most sophisticated sensor .
CA-2000 adopts a highly-selective semiconductor sensor
(reactive to alcohol substance) designed by KAIST
(Korea Advanced Institute of Science and Technology).
CA-2000 is an unique breath tester adopting this
most sophisticated technology of sensor.
02. Stable testing data
It allows you to get stable data for successive testing.
03. Digital type ; It displays by 3 digits (0.xx% BAC/BrAC).
04. Wide detection range : 0.00 - 0.40% BAC.
05. Long-term stability .
CA-2000 can analyzes very precisely
even after long time of uses.
06. Compact & light weight hand-held device.
07. Short warm-up & response Time.
After power on, less than 20sec. of warming up count-down
(200 to 000) is needed to make it ready for testing.
And, exhaling just for a few seconds will reach you
to instantly read the testing numeric digits.
08. Longer life time : 3,000 times testing.
09. Quick Recovery Time.
The sensor of CA-2000 can be purged in 30 seconds
for another time of testing.
You don't need to be too patient to do consecutive testing.
10. Power .
9V Alkaline battery & one cigar Jack DC adapter included.
11. Sanitary Testing .
CA-2000 includes 5pcs of mouthpiece for sanitary direct testing.
12. Alarm Sound.
If you are out of legal limit range, alarm sound
will be automatically beeping.
It could be customized depending on the countries.
13. Compact design and anaesthetic outlook .
HOW TO USE
1. Turn on the PWR On/Off switch
Soon after the power on, CA-2000 will start the
count-down 200 to 000 on the display window.
It is a "Warm-up" process to make the sensor,
and circuit be ready for testing.
2. When you hear beep sound & green lighting is on READY,
please blow into for 3 seconds till you would hear
another time of "Beep" sound.
N.B. : 1. In this stage, if you don't blow within 30 seconds,
it automatically shows OFF display for turn-off
3. In case you drink quite a little
(if actual concentration would be below 0.01% BAC/0.05 mg/lBrAC),
it may not be activated.
However, it shows still 0.00% and you're said to be in safe range.
4. Then, the test result (BAC or BrAC) will be displayed
by 3 digits for 15 seconds, at the same time both READY,
and WARN lamps are flickering.
N.B. : 1. If the BAC / BrAC data would be over
0.05% / 0.25mg/l (default setting) respectively,
red WARN lamp will be flickering along with "Alarm" sound.
5. The "Alarm" level is adjustable pursuant to the local legal limit.
6. Finally, it shows "OFF" for turn-off.
7. For the successive testing, try again from No.1 to No. 3.
TO GET MORE ACCURATE TESTING DATA
After drinking, it is recommended to test after 30 min.
It is because it takes 30 min. approximately for alcohol
to be absorbed into blood, from the digestive organs.
And residual alcohol remaining in the mouth
may cause inaccurate data.
To avoid testing under strong wind or in the closed room
with contaminated air.
When the "BAT LOW "lamp is lighting on, it's advisable to
replace 9V alkaline battery.
To attain more accurate data, please repeat testing about 3 times.
TECHNICAL SPECIFICATION
- Size : 12 x 6 x 2,5 cm
- Weight : 200g
- Housing : Shock resistant, molded plastic
- Sensor : Highly selective semi-conductive oxide alcohol sensor
- Response time : 3 sec.
- Warm up time : 20 sec.
- Recovery time (sensor purge) : 30 sec.
- Battery life : About 200 tests
- Battery : 9V alkaline
- External power supply : 12V DC adapter
- Accuracy : at ± 0.01% at 0.10% BAC
at ± 0.05 mg/l at 0.50mg/l BrAC.
- Detection range : 0.00 ~ 0.40% BAC . 0.00 ~ 2.00 mg/l BrAC
- Calibration : BAC simulator (Model 34C/Guth Laboratory, USA)
- Digital display : Three digits in numeric readout
- Packing : Tester, 9V alkaline, Cigar-Jack DC adapter,
- 5 pcs of mouthpieces, Users manual, Carrying Bag .
- Measuring method : Variation of Electro- Conductivity
Deviation at 0.10% BAC : at ± 0.01% BAC
- Characteristics : High selectivity , Reasonable price , small deviation .
O
.